CLBM 2008
 |
 |
 |
 |
 |
 |
 |
 |
| Traveler Front Cage Kit Our Exclusive Plate Design Front Cage Kit: NO TUBES IN THE WAY The Ultimate In Usability, Style & Design! Available alone, or in a package with a roll bar kit. |
| The Scout II Front Cage also works for a Traveler!: We use a water jetted, hand bent plate along the side of the dash, ELIMINATING all tubes below the dash. The front arms are designed to fit all the way to the outside of the hardtop, eliminating annoying bars directly over your head. |
| The Scout II Front Cage also works for a Traveler!: However, CB Bars do NOT work in a Traveler. This is due to the strip running along the interior of your hardtop, between the front and rear seats. It is lower than the rest of the roof, and lower than a Scout II roof. Thus, it directly interferes with CB Bars. Consequently, CB Bars ARE NOT AVAILABLE with a front cage kit for a Traveler. |
| Our Most Exciting Product! Works With Our Traveler Rollbar to Make a 6-Pt Front Cage Available Separately, or as a Package with a Rollbar |
For just the front cage, you will need either our roll bar, or a factory 2-inch roll bar (that mounts on top of the step
behind the front seats, NOT the floor behind your front seats) to use this kit. If you don't have a roll bar, you will need
our roll bar and front cage kit package available on the order page by clicking Click Here to Order.
This front cage kit will work with our Traveler roll bar to give you a 6-pt cage that will enclose the front area of your
Scout from the front windshield to the rear wheel well humps.
We use 0.120 wall 2-inch HREW for the tubing, and the custom designed plate is 3/8-inch thick. This kit will fit
perfectly under a hard top, while still being as out of the way as possible.
This is a kit, and you will install it yourself. Front Cage Kit includes two forward-reaching arms, two cross member
tubes, all pieces for the custom plate, and mounting plates for the back side of the kick panel.
Installation will require the following (in the order you prefer):
It's easiest to remove your top and doors for installation. Your body mount bolts will need to be removed, and it's
important that the floor be intact and mostly rust free.
Each plate consists of 6 pieces, which you will assemble and tack weld inside your Scout. Then you remove the plates,
and solidly weld them with a 220 welder. It's thick steel, and your cage will only be as good as your welds, so have a
professional do this if you aren't comfortable doing it yourself. Once your plates are complete, you will bolt them into
your Scout. Bolts go through to your body mount, and through your kick panel. After the plates are installed, you will
fit the arms to exactly the right length. Each arm has a little extra length, so you can get the perfect fit. You can use a
tube notcher, torch, grinder, or sawzall to fit the arms perfectly to your roll bar and the plate. Then the two cross
members are installed, one at the top near the visors, and one right over the dash.
PLEASE NOTE: There is one spot where the tube and plate come together that is very difficult to weld, between the
plate and your windshield.
| $340 Front Cage Only $525 Front Cage & Roll Bar Plus Shipping |
WARNING: These are technically considered show bars, as we cannot guarantee their performance in case of a rollover. Off-roading
and even highway driving are inherently dangerous, and loss of life or other injuries can occur. We simply cannot be held
responsible for the performance of an installed kit. We have listed them as "rollbars" only so you could find them using the eBay
search engine. This is a kit, you are installing it, you are welding it, you are bolting it, and therefore you are 100% responsible for it's
performance and you cannot hold us liable for any bodily or property harm. Sorry, but that's how it works with safety devices you will
buy from anyone, so we just had to say it. These are made to the best of our ability with good steel, but we simply cannot take
responsibility for their use. You all know a crazy off-roader, so you know why this is so important. YOUR BID OR PURCHASE IS A
LEGALLY BINDING ACCEPTANCE OF THIS LIABILITY RELEASE.
PAYMENT DETAILS: Payment by credit card, debit card, or PayPal balance upon checkout.
$85 (front cage only) or $160 (front cage and roll bar) FLAT SHIPPING TO ANY PHYSICAL ADDRESS IN THE LOWER 48 STATES
Roll bar kits general ship in 24-48 business hours. Front and full cages take from 1-7 days to ship (usually the Monday after you
order).
and even highway driving are inherently dangerous, and loss of life or other injuries can occur. We simply cannot be held
responsible for the performance of an installed kit. We have listed them as "rollbars" only so you could find them using the eBay
search engine. This is a kit, you are installing it, you are welding it, you are bolting it, and therefore you are 100% responsible for it's
performance and you cannot hold us liable for any bodily or property harm. Sorry, but that's how it works with safety devices you will
buy from anyone, so we just had to say it. These are made to the best of our ability with good steel, but we simply cannot take
responsibility for their use. You all know a crazy off-roader, so you know why this is so important. YOUR BID OR PURCHASE IS A
LEGALLY BINDING ACCEPTANCE OF THIS LIABILITY RELEASE.
PAYMENT DETAILS: Payment by credit card, debit card, or PayPal balance upon checkout.
$85 (front cage only) or $160 (front cage and roll bar) FLAT SHIPPING TO ANY PHYSICAL ADDRESS IN THE LOWER 48 STATES
Roll bar kits general ship in 24-48 business hours. Front and full cages take from 1-7 days to ship (usually the Monday after you
order).
| $340 Front Cage Only $525 Front Cage & Roll Bar Package Plus Shipping |
Interested in just the front plates, so you can make your own cage? Click Here